NORWAY · WELLBORES · NPDID 4053
30/3-9
Exploration · Wildcat · P&A · Gas/condensate · Den norske stats oljeselskap a.s · PL 052
What was run in 30/3-9 and how the hole was built: the logs with their intervals, the casing strings with leak-off tests, and the mud at depth.
Logs you can open: composite and completion logs on file
- Composite logpdf · 540 KB
- Completion logpdf · 63.2 MB
The table below says which logs were run and over what interval. The curves themselves are held in Diskos, Norway's national data repository; its public portal lists what has been released for a wellbore and can be ordered for an administrative fee. Diskos public portal →
Logs
| Log | Top, m | Base, m | Composite log for the well |
|---|---|---|---|
| MWD - CDRMWD measurement while drilling · CDR compensated dual resistivity | 203 | 3,712 | On file: open → |
| DSI LDL LEH QT GRDSI dipole shear sonic imager · LDL litho-density log · GR gamma ray | 1,020 | 2,459 | On file: open → |
| DSI CSI (VSP) GRDSI dipole shear sonic imager · VSP vertical seismic profile · GR gamma ray | 1,816 | 3,925 | On file: open → |
| VSPVSP vertical seismic profile | 1,860 | 4,000 | On file: open → |
| DITE DSI LDT ACTS GRDITE phasor dual induction · DSI dipole shear sonic imager · LDT litho-density tool · ACTS auxiliary compression and tension sub · GR gamma ray | 2,452 | 3,719 | On file: open → |
| FMI GRFMI formation micro-imager · GR gamma ray | 3,687 | 3,949 | On file: open → |
| DLT MSFL LDT CNT GRMSFL micro-spherically focused log · LDT litho-density tool · CNT compensated neutron tool · GR gamma ray | 3,712 | 4,023 | On file: open → |
| MWD - ARCMWD measurement while drilling · ARC array resistivity compensated | 3,712 | 4,015 | On file: open → |
| MSCT GRMSCT mechanical sidewall coring tool · GR gamma ray | 3,807 | 3,925 | On file: open → |
| MDT GRMDT modular formation dynamics tester · GR gamma ray | 3,809 | 3,919 | On file: open → |
Casing and leak-off tests
| Casing | Diameter, in | Depth, m | Hole, in | Hole depth, m | LOT/FIT, g/cm³ | Test |
|---|---|---|---|---|---|---|
| Conductor | 30 | 201 | 36 | 201 | 0 | LOT |
| Interm. | 20 | 1,019 | 26 | 1,019 | 1.6 | LOT |
| Interm. | 13 3/8 | 2,452 | 17 1/2 | 2,454 | 1.91 | LOT |
| Interm. | 9 5/8 | 3,707 | 12 1/4 | 3,707 | 2.05 | LOT |
| Open hole | — | 4,015 | 8 1/2 | 4,015 | 0 | LOT |
Drilling mud
30 READINGS · BY DEPTH
| Depth, m | Weight, g/cm³ | Viscosity, mPa·s | Yield point, Pa | Type |
|---|---|---|---|---|
| 180 | 1.03 | 0 | 0 | Dummy |
| 730 | 1.6 | 15 | 0 | Glydrill |
| 737 | 1.82 | 22 | 0 | Glydrill |
| 748 | 1.6 | 16 | 0 | Glydrill |
| 905 | 1.82 | 23 | 0 | Glydrill |
| 950 | 1.82 | 25 | 0 | Glydrill |
| 1,027 | 1.2 | 0 | 0 | Dummy |
| 1,328 | 1.24 | 12 | 0 | Glydrill |
| 1,879 | 1.45 | 18 | 0 | Glydrill |
| 2,113 | 1.6 | 26 | 0 | Glydrill |
| 2,123 | 1.6 | 24 | 0 | Glydrill |
| 2,159 | 1.58 | 19 | 0 | Glydrill |
| 2,460 | 1.6 | 24 | 0 | Glydrill |
| 2,463 | 1.61 | 21 | 0 | Glydrill |
| 2,542 | 1.75 | 50 | 0 | Versapro |
| 2,542 | 1.78 | 50 | 0 | Versapro |
| 2,885 | 1.75 | 50 | 0 | Versapro |
| 3,438 | 1.78 | 51 | 0 | Versapro |
| 3,457 | 1.78 | 50 | 0 | Versapro |
| 3,536 | 1.81 | 53 | 0 | Versapro |
| 3,707 | 1.82 | 48 | 0 | Versapro |
| 3,712 | 1.82 | 48 | 0 | Versapro |
| 3,718 | 1.89 | 26 | 0 | Versapro |
| 3,808 | 1.91 | 31 | 0 | Glydrill |
| 3,810 | 1.91 | 26 | 0 | Glydrill |
| 3,899 | 1.91 | 28 | 0 | Glydrill |
| 3,909.2 | 1.91 | 32 | 0 | Glydrill |
| 3,926 | 1.91 | 29 | 0 | Glydrill |
| 3,975 | 1.91 | 30 | 0 | Glydrill |
| 4,015 | 1.91 | 28 | 0 | Glydrill |
The words under each tool string are Petrora's reading of the standard codes in it; a code we do not recognize is left as filed. The composite log is one file for the whole well. The Directorate does not say which runs or depths it draws on, so the link is the same on every row.
About this data
Norwegian Offshore Directorate (Sodir) FactPages, mirrored nightly and used under the Norwegian Licence for Open Government Data (NLOD). Log names are the Directorate's tool strings as filed; the plain-word readings beside them are Petrora's, from common industry abbreviations. Depths are metres along the wellbore from the kelly bushing; diameters are inches, as filed.
Developers: this page as JSON is GET /v1/data/norway/wells/4053, documented in the API reference.